High-Performance Polymers
70 entries in this category — Page 3 of 4
High-performance polymers are advanced thermoplastics capable of continuous service above 150°C, offering exceptional chemical resistance, mechanical strength, and dimensional stability. Covering PEEK, Ultem (PEI), PTFE, PPS, LCP, polyimide (Vespel), PAI (Torlon), PES, PSU, PPSU, PEK, PFA, ETFE, and FEP, these materials are specified for aerospace, medical implant, semiconductor, and oil & gas applications where standard engineering plastics fail. Key selection factors: continuous service temperature, chemical resistance, processing requirements, and cost.
PA12 Nylon: Low-Moisture Polyamide for Automotive Tubing
Tensile: 50 MPa · HDT: 55 °C at 1.82 MPa
PA12 has lowest moisture absorption of any polyamide (0.25% vs 2.5-3.0% for PA66). Material of choice for fuel lines, air brake tubing, pneumatic...
View Details →PEEK 450FC30: Food Contact Bearing Grade
Tensile: 180 MPa · HDT: 310 °C
Victrex food-contact certified wear-resistant grade with PTFE lubricant. FDA and EU 10/2011 compliant. PV limit: 4.5 MPa·m/s. For meat processing,...
View Details →Torlon 4301: High-PV Bearing Grade PAI for Aerospace
Tensile: 130 MPa · HDT: 278 °C
Bearing-grade PAI with graphite/PTFE lubrication. PV limit 7.0 MPa·m/s — competes with Vespel SP-21 at 60% cost. For flap track liners, landing...
View Details →Semitron ESD PEEK: Static-Dissipative for Semiconductor
Tensile: 95 MPa · HDT: 250 °C
Carbon-nanotube-filled for ESD protection (10^6-10^9 Ω/sq). ESD damage costs K-50K per wafer at advanced nodes. Outgassing Propprose...
View Details →PEEK CF30 (30% Carbon Fiber): Maximum-Strength High-Temperature Thermoplastic Properties
Tensile: 220 MPa · HDT: 315 °C at 1.82 MPa
PEEK CF30 (30% carbon fiber reinforced) is the highest-strength injection-moldable PEEK grade, offering 220 MPa tensile strength — more than...
View Details →PEEK GF30 (30% Glass Fiber): Cost-Effective Reinforced High-Temperature Polymer
Tensile: 160 MPa · HDT: 300 °C at 1.82 MPa
PEEK GF30 (30% glass fiber reinforced) is the most cost-effective reinforced PEEK grade, offering 60% higher tensile strength than unfilled PEEK...
View Details →PPS Ryton GF40 (40% Glass Fiber): Maximum-Strength Chemical-Resistant Polymer
Tensile: 160 MPa · HDT: 265 °C at 1.82 MPa
PPS GF40 (40% glass fiber reinforced) is the standard high-performance PPS grade for structural applications. With 160 MPa tensile strength at...
View Details →LCP Vectra E130i: 30% Glass-Fiber Liquid Crystal Polymer for Precision Connectors
Tensile: 150 MPa · HDT: 275 °C at 1.82 MPa
LCP Vectra E130i is a 30% glass-fiber reinforced liquid crystal polymer specifically formulated for ultra-fine-pitch electronic connectors. Its...
View Details →Torlon 5030 PAI (30% Glass Fiber): Highest-Strength Injection-Moldable Thermoplastic
Tensile: 200 MPa · HDT: 282 °C at 1.82 MPa
Torlon 5030 (30% glass fiber reinforced PAI) achieves the highest tensile strength (200 MPa) and HDT (282°C) of any injection-moldable...
View Details →Ultem 2300 PEI (30% Glass Fiber): High-Strength Flame-Retardant Amorphous Polymer
Tensile: 140 MPa · HDT: 210 °C at 1.82 MPa
Ultem 2300 (30% glass fiber reinforced PEI) is the strength-optimized grade of Ultem, offering 140 MPa tensile strength with the inherent UL94 V-0...
View Details →PPS Ryton R-4 XT: Extended-Toughness Glass Fiber Polymer for Automotive
Tensile: 150 MPa · HDT: 265 °C at 1.82 MPa
PPS Ryton R-4 XT is an extended-toughness variant of the standard R-4 grade, offering improved impact resistance (notched Izod ~95 J/m vs ~80 J/m...
View Details →PPS GF40 Reinforced: High-Temperature Chemical-Resistant Engineering Plastic
Tensile: 160 MPa · HDT: 265 °C at 1.82 MPa
PPS GF40 is the most cost-effective high-temperature reinforced thermoplastic — offering 265°C HDT and exceptional chemical resistance at 40-50%...
View Details →LCP Vectra A130: 30% Glass-Fiber High-Flow Liquid Crystal Polymer
Tensile: 150 MPa · HDT: 260 °C at 1.82 MPa
LCP A130 is the standard 30% glass-fiber LCP grade for precision electronic connectors with 0.5mm pitch and wall thicknesses as low as 0.2mm —...
View Details →PA46 Stanyl: High-Temperature Nylon for Automotive and Electronics
Tensile: 100 MPa (unfilled) / 210 MPa (30% GF) · HDT: 290 °C (30% GF)
PA46 (Stanyl) bridges the gap between PA66 and PPA/PPS — offering 295°C melting point with nylon-level toughness and flowability. Used for...
View Details →PPSU Radel R-5100: Maximum-Toughness High-Temperature Transparent Polymer
Tensile: 76 MPa · HDT: 207 °C at 1.82 MPa
PPSU Radel offers the highest impact resistance of any amorphous high-temperature polymer — notched Izod 690 J/m (no break) — with inherent flame...
View Details →PES Ultrason E: High-Temperature Transparent Polymer for Medical and Food Contact
Tensile: 85 MPa · HDT: 204 °C at 1.82 MPa
PES offers the best combination of high-temperature performance, transparency, and hydrolytic stability among amorphous polymers — the standard...
View Details →Ultem 1000 PEI Unfilled: Transparent Flame-Retardant High-Temperature Polymer
Tensile: 105 MPa · HDT: 200 °C at 1.82 MPa
Ultem 1000 is the foundational PEI grade — offering inherent UL94 V-0 flame retardancy without additives, excellent dielectric properties, and...
View Details →PTFE 25% Glass-Filled: Enhanced Wear Resistance & Dimensional Stability
Tensile: 25 MPa · HDT: 120 °C at 1.82 MPa
PTFE 25% glass-filled combines the universal chemical resistance of pure PTFE with significantly improved dimensional stability and wear...
View Details →PFA Ultra-High Purity Grade: Semiconductor & Pharmaceutical Fluid Handling
Tensile: 28 MPa · HDT: 75 °C at 1.82 MPa
PFA (perfluoroalkoxy) is the melt-processable sibling of PTFE — it delivers near-identical chemical resistance while being injection-moldable and...
View Details →PEEK CLASSIX Implant Grade: Medical Device & Long-Term Implant Material
Tensile: 100 MPa · HDT: 160 °C at 1.82 MPa
PEEK implant grades are a distinct category of PEEK polymer specifically manufactured under ISO 13485 quality systems for long-term implantable...
View Details →