PEEK 450G: Properties, Uses & Cost Guide
Tensile data verified against MatWeb.com database & manufacturer datasheets · Last updated July 2026
Published: 2026-05-31
PEEK 450G is the unfilled, general-purpose grade of PEEK using Victrex's standard molecular weight. It is the benchmark against which all other PEEK grades are measured, and is the preferred grade for medical implant (long-term implantable per...
PEEK 450G is the unfilled, general-purpose grade of PEEK using Victrex's standard molecular weight. It is the benchmark against which all other PEEK grades are measured, and is the preferred grade for medical implant (long-term implantable per ISO 10993, USP Class VI, FDA Master File), pharmaceutical processing, and food contact applications where carbon fiber or glass fiber additives are undesirable (particle shedding, surface roughness on sealing faces, or regulatory restrictions). The '450' denotes medium-viscosity optimized for injection molding; 'G' denotes general-purpose powder/granulate form.
PEEK 450G is processed at 360-400°C melt temperature with 160-200°C mold temperature. The semicrystalline microstructure after proper processing (approximately 30-35% crystallinity) provides the characteristic balance of strength, stiffness, chemical resistance, and wear resistance. Inadequate mold temperature (<150°C) quenches the polymer into a predominantly amorphous state — transparent amber color, lower strength, poor chemical resistance, and recrystallization in service causing dimensional change up to 1.2% (linear) as the part cycles above Tg (143°C). Correctly processed PEEK 450G is opaque beige/tan — the opacity comes from spherulitic crystalline structures scattering light.
Recommended Applications
PEEK 450G Unfilled is commonly specified for:
⚠ Not Recommended For
PEEK 450G Unfilled is not recommended for:
- Food contact without FDA-grade certification (Classix or 450G compliant grades only)
- Outdoor UV exposure without UV-stabilized grade (unfilled PEEK yellows and embrittles under UV)
- High-impact shock loading below -60°C (becomes brittle; consider PAI or PI instead)
Selection & Application Guide
PEEK is the material of choice when your application demands continuous service above 250°C, outstanding chemical resistance across a wide pH range, and high mechanical strength simultaneously. Choose PEEK over PTFE when load-bearing capacity matters, over Ultem when temperatures exceed 180°C, and over PPS when toughness and elongation are critical. PEEK justifies its premium cost ($80-200/kg) in aerospace, oil & gas downhole, and medical implant applications where failure is not an option.
Real-World Applications
PEEK's radiolucency (invisible on X-ray/CT) combined with bone-matching modulus makes it the standard for interbody spinal fusion devices per ASTM F2026.
PEEK withstands H2S, amine inhibitors, and 200°C+ temperatures at depth — replacing metal components that corrode in aggressive well environments.
PEEK's low particle generation, chemical resistance to strong acids, and dimensional stability at elevated temperatures make it ideal for cleanroom wafer handling.
Carbon-fiber reinforced PEEK (CA30) provides wear resistance and thermal stability for high-temperature dynamic sealing in automotive transmissions.
Processing & Cost Considerations
Manufacturing Tips
- Melt temperature must be 380-400°C with mold temperature 160-200°C — standard injection molding machines cannot process PEEK. You need a high-temperature package with ceramic heater bands and oil-heated mold system.
- Drying is critical: PEEK is hygroscopic and must be dried at 150-160°C for 3-4 hours to reach moisture content below 0.02%. Processing wet PEEK causes hydrolysis, brown discoloration, and loss of mechanical properties.
- Mold temperature controls crystallinity: below 150°C produces amorphous parts (transparent amber, lower strength); 160-180°C yields optimal semi-crystalline structure (30-35% crystallinity, opaque tan).
PEEK raw material costs $80-200/kg depending on grade (unfilled 450G is $150-200/kg, CF-reinforced $180-250/kg). Machine premium adds 30-50% for high-temperature capability. Oil-heated mold systems cost $20,000-50,000 additional. Total molded part cost runs 5-10x higher than nylon or polycarbonate. Optimize by minimizing wall thickness to reduce material usage, using unfilled grade when reinforcement isn't needed, and considering PPS as a lower-cost alternative when service temperature stays below 200°C.
Technical Properties
| Density | 1.30 g/cm³ |
|---|---|
| Tensile Strength | 100 MPa |
| Melting Point | 343 °C |
| Shrinkage Rate | 1.2% |
| Flexural Modulus | 4.1 GPa |
| Hdt | 160 °C at 1.82 MPa |
| Continuous Service Temp | 260 °C |
Engineering Tool: Shrinkage & Cost Estimator
Calculate part weight, mold cavity dimensions accounting for shrinkage, and material cost — all locally in your browser.
Equivalents & Cross-References
| Equivalent / Alternate | Action |
|---|---|
| Victrex PEEK 450G | |
| Evonik Vestakeep 1000G | |
| Solvay KetaSpire KT-820 |
Frequently Asked Questions
Can PEEK be used for FDA-compliant food contact applications?
Yes. Unfilled PEEK complies with FDA 21 CFR 177.2415 for repeated food contact. It also meets USP Class VI and ISO 10993 biocompatibility standards for medical devices. Always verify the specific grade with the manufacturer — colorants and fillers may affect compliance.
Is PEEK resistant to steam autoclaving?
Yes. PEEK withstands repeated autoclave cycles at 134°C and 2 bar pressure — one of the few thermoplastics suitable for this sterilization method. It resists hydrolysis in steam environments, making it standard for reusable surgical instruments and dental components.
What is the difference between PEEK and PEKK?
PEKK (polyetherketoneketone) has a higher glass transition temperature (165°C vs 143°C for PEEK) and can be processed at lower temperatures due to its lower crystallization rate. PEKK offers comparable chemical resistance but different crystallization behavior — it can be quenched to an amorphous state more easily than PEEK. PEKK costs 20-40% more than PEEK.
Can PEEK be machined instead of injection molded?
Yes. PEEK is readily machined on CNC equipment using carbide or diamond tooling. Machined PEEK parts are common for prototyping and low-volume aerospace components. However, machining generates significant material waste (PEEK costs $150+/kg), so injection molding is more economical for volumes above 500-1000 pieces.
Does PEEK outgas in vacuum environments?
PEEK has exceptionally low outgassing characteristics — TML (Total Mass Loss) below 1.0% and CVCM (Collected Volatile Condensable Materials) below 0.1% per ASTM E595. This makes PEEK suitable for satellite and space applications where vacuum compatibility is required.
Related Diagnostics & Materials
PEEK Polyetheretherketone: High-Performance Polymer...
Polyetheretherketone (PEEK) is a colorless organic thermoplastic polymer in the polyaryletherketone (PAEK) family,...
Ultem PEI (Polyetherimide): High-Temperature Amorphous...
Polyetherimide (PEI), best known by Sabic's trade name Ultem, is an amorphous high-performance thermoplastic...
PTFE Teflon: Ultimate Chemical Resistance & Low-Friction...
Polytetrafluoroethylene (PTFE), widely known by the trade name Teflon, is a fluoropolymer with the lowest...
PPS Ryton: Polyphenylene Sulfide High-Temp...
Polyphenylene sulfide (PPS), best known by Solvay's trade name Ryton, is a semicrystalline high-performance...
LCP Vectra: Liquid Crystal Polymer for Micro-Molding &...
Liquid Crystal Polymer (LCP), best known by Celanese's trade name Vectra, is a unique class of thermotropic...
Vespel Polyimide: Extreme-Temperature Polymer for...
Polyimide (PI), commercially known as DuPont Vespel, is the highest-temperature-rated polymer commercially...
PAI Torlon: Polyamide-Imide Extreme-Performance Polymer...
Polyamide-imide (PAI), commercially known as Solvay Torlon, occupies the performance space between PEEK and...
PES Veradel: Polyethersulfone Transparent High-Temp...
Polyethersulfone (PES), commercially known as Solvay Veradel or BASF Ultrason E, is an amorphous high-temperature...
References & Industry Standards
- ASTM International. Standard Specifications for Engineering Plastics & Thermoplastics. astm.org
- UL Prospector. Plastics & Elastomers Material Database. ulprospector.com
- MatWeb. Material Property Data for Engineering Thermoplastics. matweb.com
- ISO 1043. Plastics — Symbols and Abbreviated Terms. iso.org