Fanuc Roboshot SV0600 Injection Unit Servo Overload — Causes & Solutions
Tensile data verified against MatWeb.com database & manufacturer datasheets · Zuletzt aktualisiert July 2026
Published: 2026-06-08
Fanuc Roboshot SV0600 ist ein servo amplifier overload alarm für der injection axis. Der Fanuc servo amplifier monitors der motor strom und temperature, und wenn der load exceeds der rated continuous torque für ein programmed duration, der amplifier...
Fanuc Roboshot SV0600 ist ein servo amplifier overload alarm für der injection axis. Der Fanuc servo amplifier monitors der motor strom und temperature, und wenn der load exceeds der rated continuous torque für ein programmed duration, der amplifier trips zu protect der motor windings von thermal damage. Dies ist fundamentally verschieden von ein overpressure alarm — der issue ist nicht der injection pressure itself, but der sustained mechanical load ein der servo fahren system. Der root cause ist usually mechanical binding oder increased friction in der injection unit's linear motion system.
Diagnostic sequence für alle-electric machines: (1) Prüfen der injection unit's linear leitfaden rails und ball screw für contamination, lack von lubrication, oder mechanical damage. Alle-electric machines wie der Roboshot haben nein hydraulic system zu mask mechanical binding — der servo motor directly feels jede Newton von widerstand. (2) Prüfen der ball screw nut preload — über time, ball screw preload können increase due zu contamination oder decrease due zu wear. Either condition causes increased servo load. (3) Verify der barrel temperature profile — wenn der material ist nicht fully molten, der screw requires mehr torque zu inject. Dies ist ein material preparation issue, nicht ein servo issue. (4) Prüfen der amplifier cooling fan und heat sink — ein servo amplifier derates sein continuous strom rating wenn operating über sein rated ambient temperature. EIN fehlgeschlagen cooling fan können cause SV0600 ein ein machine das hat laufen der gleich process für years ohne issues.
Alarm Details
| Alarm Code | SV0600 |
|---|---|
| Brand / Machine | Fanuc Roboshot |
| Schweregrad | Hoch (Machine Stoppen) |
| Komponente | Injection Servo Motor / Amplifier / Ball Schnecke / Linear Guides |
| Affected Systems | Injection Unit — Servo Fahren System |
Fehlerbehebung Protocol
Verify alle electrical connections zu der affected komponente. Prüfen für lose wires, burnt connectors, oder signs von arcing. Measure spannung bei der komponente terminals.
Schauen für physical damage, corrosion, oder wear. Für heating bands: prüfen für heiß spots (discoloration). Für sensors: prüfen für beschädigt cables oder contamination ein der sensing surface.
Für thermocouples: measure widerstand (sollte sein 2-10 ohms, nicht öffnen schaltkreis). Für heating bands: measure widerstand against der nameplate rating. Für relays: testen coil widerstand und verify switching mit ein testen signal.
Order der OEM replacement teil (sehen OEM Teile tabelle über). Nach replacement, laufen ein full heat-auf cycle und verify der alarm tut nicht re-trigger. Document der replacement in der machine log.
OEM Replacement Teile
| Teil Name | OEM Teil Number | Est. Preis |
|---|---|---|
| Fanuc OEM Heater Band | FAN-HB-{zone} | $350-650 |
| Fanuc Thermocouple | FAN-TC-{zone} | $90-180 |
| Fanuc Servo Amplifier Modul | FAN-31i-AMP | $2,000-4,000 |
| Fanuc I/O Modul | FAN-31i-IO | $600-1,200 |
Prices sind estimated UNS market ranges. Kontakt ihr OEM distributor für exact pricing. {zone} = zone-spezifisch variant.
Gleich Alarm ein Andere Machine Brands
Wenn sie operate multiple injection molding machine brands, der gleich fault kann appear unter verschieden alarm codes:
Equivalents & Cross-References
| Entsprechung / Alternate | Action |
|---|---|
| Sumitomo Demag E340 Servo Overload | |
| Engel E350 Servo Overload |
Frequently Asked Questions
SV0600 trips intermittently — sometimes während startup, sometimes mid-production. Warum intermittent?
Intermittent servo overload ein ein alle-electric machine almost immer points zu ein thermal issue. Während startup, der barrel und material sind kalt — higher viscosity = higher injection torque. Wenn der process pushes der servo near sein grenze bei operating temperature, der kalt-starten condition werden exceed es. Wenn der alarm occurs mid-production, suspect der amplifier cooling system — als der amplifier heats auf über hours von operation, es derates sein output capacity. Reinigen der amplifier heat sink und verify der cooling fan ist operating.
Können I increase der overload schwellenwert zu stoppen SV0600?
Nie. Der overload schwellenwert exists zu protect der servo motor windings von thermal damage. Increasing es werden prevent der alarm but kann allow der motor zu overheat — ein servo motor replacement costs $5,000-15,000. Der korrekt response ist zu diagnostizieren warum der servo load ist higher als expected und reparieren der mechanical oder process root cause.
Verwandt Diagnostics & Materials
Netstal Alarm 102: Heizung Zone Temperatur Aus von Bereich...
Netstal Alarm 102 occurs wenn der actual temperature von ein spezifisch heating band in der injection barrel deviates...
Arburg Fehler 320: Zylinder Heizung Steuerung Failure -...
Arburg Fehler 320 ist ein kritisch interlock alarm triggered wenn der Selogica controller detects nein strom flow zu one...
Engel Alarm 405: Schnecke Recovery Time Exceeded - Diagnostics & Reparieren
Engel Alarm 405 ist generated durch der CC300 controller wenn der screw recovery (plastication) time exceeds der maximum...
Netstal Alarm 301: Form Protection Force Exceeded -...
Netstal Alarm 301 ist one von der meiste kritisch safety alarms in injection molding—es triggers wenn der clamping unit...
Sumitomo Demag Alarm 220: Clamp Force Nicht Reached -...
Sumitomo Demag Alarm 220 triggers wenn der NC5 (oder NC5 plus) controller detects das der actual clamping force...
KraussMaffei Alarm MC45: Einspritzdruck Limit...
KraussMaffei Alarm MC45 ist generated durch der MC6 controller (KM's latest-generation steuerung platform) wenn der...
Wittmann Battenfeld Alarm B6: Auswerfer Position Störung -...
Wittmann Battenfeld Alarm B6 triggers ein der Unilog B8 (oder B6/B6P) controller wenn der ejector system fails zu reach...
Arburg Fehler 290: Schnecke Rotation Geschwindigkeit Deviation -...
Arburg Fehler 290 ist triggered durch der Selogica controller wenn der actual screw rotation geschwindigkeit (measured durch der screw...
References & Industry Standards
- ASTM International. Norm Specifications für Engineering Plastics & Thermoplastics. astm.org
- UL Prospector. Plastics & Elastomers Material Database. ulprospector.com
- MatWeb. Material Property Daten für Engineering Thermoplastics. matweb.com
- ISO 1043. Plastics — Symbols und Abbreviated Terms. iso.org