Ultem 2300 (30% Glass-Filled PEI) Eigenschaften — Complete Engineering Daten Sheet (2026)
Tensile data verified against MatWeb.com database & manufacturer datasheets · Zuletzt aktualisiert July 2026
Published: 2026-05-31
Ultem 2300 ist der 30% glass-fiber-reinforced grade von polyetherimide (PEI), engineered zu bereitstellen dramatically higher stiffness, unter thermal expansion, und improved dimensional stability compared zu unfilled Ultem 1000. Der glass fiber...
Ultem 2300 ist der 30% glass-fiber-reinforced grade von polyetherimide (PEI), engineered zu bereitstellen dramatically higher stiffness, unter thermal expansion, und improved dimensional stability compared zu unfilled Ultem 1000. Der glass fiber reinforcement increases flexural modulus durch ~2.7× (9.0 GPa vs 3.3 GPa unfilled) und reduces mold shrinkage zu 0.2-0.4% (vs 0.5-0.7% unfilled) — kritisch für tight-tolerance electrical connectors, schaltkreis breaker housings, und avionics enclosures wo post-molding warpage würde cause misalignment.
Ultem 2300 ist der dominant material für hoch-temperature electrical connectors und sockets in aerospace, military, und downhole öl-und-gas applications. Es ist inherently flame-retardant (UL 94 V-0 bei 0.25 mm ohne flame-retardant additives — der polymer backbone contains aromatic imide groups das char rather als burn), hat excellent dielectric properties stable across ein wide frequency und temperature bereich, und withstands lead-kostenlos (RoHS) soldering processes (peak reflow temperatures 260°C für 30 seconds) das würde melt oder distort standard engineering thermoplastics (PBT, PA66, POM).
Processing requires hoch mold temperatures (135-165°C, öl-heated) und melt temperatures von 370-400°C. Drying ist WESENTLICH: PEI absorbs moisture rapidly von ambient luft; processing undried PEI bei 370°C causes hydrolysis (polymer chain scission) resulting in ein 30-50% loss von tensile strength und elongation — teile shatter unter load. Dry bei 150°C für minimum 4 hours (desiccant dryer, -40°C dew point) zu <0.02% moisture content.
Recommended Anwendungen
Ultem 2300 ist commonly specified für:
⚠ Nicht Recommended Für
Ultem 2300 ist nicht recommended für:
- Strong alkali environments (NaOH, KOH — PEI degrades; verwenden PPS oder PEEK für alkaline service)
- Continuous steam exposure über 180°C (verwenden PEEK oder PAI für extreme autoclave)
- Food contact ohne spezifisch FDA-compliant grade certification
Selection & Application Leitfaden
Ultem (PEI) provides der best balance von hoch-temperature leistung, processability, und kosten among amorphous hoch-temperature thermoplastics. Choose Ultem wenn continuous service temperature auf zu 170°C ist needed mit gut strength, inherent flame widerstand (UL94 V-0), und transparency options. Ultem ist easier zu process als PEEK oder Torlon und costs 60-70% less, making es der pragmatic choice wenn PEEK-level temperature widerstand isn't erforderlich.
Real-World Anwendungen
Ultem meets FAA flammability, rauch, und toxicity (FST) requirements für aircraft interior trim, tray tables, und ventilation ducts — replacing aluminum bei 40% weight savings.
Ultem's autoclave widerstand (134°C steam sterilization), rigidity, und ability zu sein gamma-sterilized machen es standard für reusable surgical werkzeug handles und dental instrument bodies.
Ultem's hoch dielectric strength, niedrig dissipation factor, und UL94 V-0 rating ohne flame retardant additives machen es der gehen-zu material für hoch-leistung electrical connectors.
Ultem's heat widerstand zu halogen bulb temperatures, dimensional stability, und metallization capability suit es für headlamp reflectors und fog licht housings.
Processing & Kosten Considerations
Manufacturing Tips
- Ultem processes bei melt temperatures von 340-425°C mit mold temperatures von 130-180°C — hoch but achievable ein viele standard machines mit hoch-temperature upgrades. Nein post-curing ist erforderlich, unlike Torlon.
- Ultem ist hygroscopic und müssen sein dried bei 150°C für 4-6 hours vor processing. Moisture content über 0.05% causes splay marks und reduced mechanical properties. Verwenden ein dehumidifying dryer für consistent results.
- Glass-filled Ultem (2300, 30% GF) provides 2× der stiffness und HDT von unfilled grade, but bei der kosten von reduced impact strength und isotropic properties. Gate design müssen account für fiber orientation in glass-filled grades.
Ultem costs $30-80/kg — significantly less als PEEK ($80-200/kg) und Torlon ($80-120/kg). Dies kosten advantage, combined mit easier processing (nein post-cure, unter mold temperatures), makes Ultem der economical hoch-temperature polymer choice für meiste applications unter 170°C. Glass-filled Ultem 2300 ist 10-15% mehr expensive als unfilled but oft eliminates der brauchen für ein mehr expensive polymer wie PEEK.
Technical Eigenschaften
| Dichte | 1.51 g/cm³ |
|---|---|
| Zugfestigkeit | 170 MPa |
| Schmelzpunkt | N/EIN (Amorphous, Tg 217 °C) |
| Shrinkage Rate | 0.4% |
| Flexural Modulus | 9.0 GPa |
| Hdt | 212 °C bei 1.82 MPa |
| Continuous Service Temp | 170 °C |
Engineering Werkzeug: Shrinkage & Kosten Estimator
Calculate teil weight, mold cavity dimensions accounting für shrinkage, und material kosten — alle locally in ihr browser.
Equivalents & Cross-References
| Entsprechung / Alternate | Action |
|---|---|
| Sabic Ultem 2300 | |
| GEHR PEI-GF30 | |
| Ensinger TECAPEI GF30 |
Frequently Asked Questions
Können Ultem ersetzen PEEK in my application?
Es depends ein ihr temperature requirement. Ultem's continuous service temperature ist 170°C vs PEEK's 260°C. Wenn ihr application stays unter 170°C und doesn't require PEEK's chemical widerstand zu aggressive solvents, Ultem provides comparable strength bei roughly half der material kosten mit easier processing. Über 170°C, PEEK ist notwendig.
Ist Ultem transparent?
Unfilled Ultem ist bernstein-transparent — es transmits licht mit ein bernstein tint, nicht wasser-clear wie polycarbonate oder acrylic. Dies makes es suitable für licht pipes und indicators wo color ist acceptable. Für wasser-clear transparency, consider polysulfone (PSU) oder optical PC instead.
Können Ultem sein sterilized?
Ja. Ultem withstands alle gemein sterilization methods: steam autoclave (134°C, 18 minutes), ethylene oxide gas, gamma radiation, und dry heat. Es maintains mechanical properties durch hundreds von autoclave cycles, making es ideal für reusable medical devices.
Was ist der difference zwischen Ultem 1000 und Ultem 2300?
Ultem 1000 ist der unfilled allgemein-purpose grade mit 105 MPa tensile strength und 217°C HDT. Ultem 2300 ist 30% glass-filled mit 186 MPa tensile strength und 210°C HDT bei 1.82 MPa. Der glass-filled grade provides viel higher stiffness but unter impact widerstand und ist opaque bernstein rather als translucent.
Tut Ultem require flame retardant additives?
Nein. Ultem achieves UL94 V-0 rating inherently bei 0.41mm thickness ohne any flame retardant additives. Dies ist ein major advantage über polycarbonate (welche requires brominated additives für V-0) für aircraft interior und electrical applications wo halogen-kostenlos flame widerstand ist specified.
Verwandt Diagnostics & Materials
PEEK Polyetheretherketone: Hoch-Leistung Polymer...
Polyetheretherketone (PEEK) ist ein colorless organic thermoplastic polymer in der polyaryletherketone (PAEK) family,...
Ultem PEI (Polyetherimide): Hoch-Temperatur Amorphous...
Polyetherimide (PEI), best known durch Sabic's trade name Ultem, ist ein amorphous hoch-leistung thermoplastic...
PTFE Teflon: Ultimate Chemical Widerstand & Niedrig-Friction...
Polytetrafluoroethylene (PTFE), widely known durch der trade name Teflon, ist ein fluoropolymer mit der lowest...
PPS Ryton: Polyphenylene Sulfide Hoch-Temp...
Polyphenylene sulfide (PPS), best known durch Solvay's trade name Ryton, ist ein semicrystalline hoch-leistung...
LCP Vectra: Liquid Crystal Polymer für Micro-Molding &...
Liquid Crystal Polymer (LCP), best known durch Celanese's trade name Vectra, ist ein unique class von thermotropic...
Vespel Polyimide: Extreme-Temperatur Polymer für...
Polyimide (PI), commercially known als DuPont Vespel, ist der highest-temperature-rated polymer commercially...
PAI Torlon: Polyamide-Imide Extreme-Leistung Polymer...
Polyamide-imide (PAI), commercially known als Solvay Torlon, occupies der leistung space zwischen PEEK und...
PES Veradel: Polyethersulfone Transparent Hoch-Temp...
Polyethersulfone (PES), commercially known als Solvay Veradel oder BASF Ultrason E, ist ein amorphous hoch-temperature...
References & Industry Standards
- ASTM International. Norm Specifications für Engineering Plastics & Thermoplastics. astm.org
- UL Prospector. Plastics & Elastomers Material Database. ulprospector.com
- MatWeb. Material Property Daten für Engineering Thermoplastics. matweb.com
- ISO 1043. Plastics — Symbols und Abbreviated Terms. iso.org