TPI Extem UH Eigenschaften — Complete Engineering Daten Sheet (2026)
Tensile data verified against MatWeb.com database & manufacturer datasheets · Zuletzt aktualisiert July 2026
Published: 2026-06-02
Extem UH thermoplastic polyimide (TPI, SABIC) represents der ober boundary von commercially available melt-processable thermoplastics — mit ein glass transition temperature (Tg) von 350°C, es exceeds PEEK (Tg 143°C) durch über 200°C. Extem UH fills...
Extem UH thermoplastic polyimide (TPI, SABIC) represents der ober boundary von commercially available melt-processable thermoplastics — mit ein glass transition temperature (Tg) von 350°C, es exceeds PEEK (Tg 143°C) durch über 200°C. Extem UH fills der gap zwischen PEEK (continuous verwenden 260°C) und non-melt-processable imidized polyimides wie Vespel und PBI Celazole. Es ist der nur amorphous thermoplastic das provides structural leistung über 300°C while seiend injection moldable — though processing demands specialized ausrüstung.
Processing extreme: melt temperature 420-440°C — meiste standard injection molding machines cannot reach dies bereich. Tooling müssen sein heated zu 220-250°C (öl heating, nicht wasser). Material müssen sein dried bei 200°C für 6+ hours. Resin kosten: approximately $500-700/kg in commercial quantities. Der extreme processing requirements restrict Extem zu applications wo nein andere thermoplastic können survive der thermal environment: semiconductor wafer handling, aerospace motor components, und downhole öl & gas tooling.
Recommended Anwendungen
TPI Extem UH ist commonly specified für:
⚠ Nicht Recommended Für
TPI Extem UH ist nicht recommended für:
- Moisture absorption applications ohne sealing (Vespel PI absorbs 1-3% moisture — dimensional stability affected)
- Kosten-sensitive applications wo PAI oder PEEK suffices (PI ist 5-10× der kosten von PEEK)
- Continuous service in strong bases über 200°C (verwenden PBI für extreme alkaline widerstand)
Technical Eigenschaften
| Dichte | 1.51 g/cm³ |
|---|---|
| Zugfestigkeit | 110 MPa |
| Schmelzpunkt | Amorphous (Tg 350°C) |
| Shrinkage Rate | 0.3-0.5% |
| Flexural Modulus | 6.2 GPa |
| Hdt | 320 °C bei 1.82 MPa |
Engineering Werkzeug: Shrinkage & Kosten Estimator
Calculate teil weight, mold cavity dimensions accounting für shrinkage, und material kosten — alle locally in ihr browser.
Equivalents & Cross-References
| Entsprechung / Alternate | Action |
|---|---|
| Extem UH 1019 | |
| Extem XH 1015 (higher flow variant) |
Frequently Asked Questions
Wie tut Extem compare zu PEEK für hoch-temperature applications?
Extem UH hat Tg 350°C vs PEEK Tg 143°C — ein 207°C advantage. Für continuous verwenden über 260°C, PEEK approaches sein mechanical limits while Extem retains structural integrity. However, PEEK costs ~$80-100/kg vs ~$500-700/kg für Extem. Der choice depends ein whether der temperature requirement können sein met durch PEEK (auf zu 260°C) oder requires der extreme leistung von TPI.
Können my injection molder process Extem?
Meiste cannot. Extem requires: 1) melt temperature 420-440°C (special barrel/ screw metallurgy), 2) mold temperature 220-250°C (öl heating, nicht wasser), 3) drying bei 200°C für 6+ hours, und 4) experience mit ultra-hoch-temperature amorphous materials. Nur specialized molders mit hoch-temperature capability können process Extem.
Verwandt Diagnostics & Materials
PEEK Polyetheretherketone: Hoch-Leistung Polymer...
Polyetheretherketone (PEEK) ist ein colorless organic thermoplastic polymer in der polyaryletherketone (PAEK) family,...
Ultem PEI (Polyetherimide): Hoch-Temperatur Amorphous...
Polyetherimide (PEI), best known durch Sabic's trade name Ultem, ist ein amorphous hoch-leistung thermoplastic...
PTFE Teflon: Ultimate Chemical Widerstand & Niedrig-Friction...
Polytetrafluoroethylene (PTFE), widely known durch der trade name Teflon, ist ein fluoropolymer mit der lowest...
PPS Ryton: Polyphenylene Sulfide Hoch-Temp...
Polyphenylene sulfide (PPS), best known durch Solvay's trade name Ryton, ist ein semicrystalline hoch-leistung...
LCP Vectra: Liquid Crystal Polymer für Micro-Molding &...
Liquid Crystal Polymer (LCP), best known durch Celanese's trade name Vectra, ist ein unique class von thermotropic...
Vespel Polyimide: Extreme-Temperatur Polymer für...
Polyimide (PI), commercially known als DuPont Vespel, ist der highest-temperature-rated polymer commercially...
PAI Torlon: Polyamide-Imide Extreme-Leistung Polymer...
Polyamide-imide (PAI), commercially known als Solvay Torlon, occupies der leistung space zwischen PEEK und...
PES Veradel: Polyethersulfone Transparent Hoch-Temp...
Polyethersulfone (PES), commercially known als Solvay Veradel oder BASF Ultrason E, ist ein amorphous hoch-temperature...
References & Industry Standards
- ASTM International. Norm Specifications für Engineering Plastics & Thermoplastics. astm.org
- UL Prospector. Plastics & Elastomers Material Database. ulprospector.com
- MatWeb. Material Property Daten für Engineering Thermoplastics. matweb.com
- ISO 1043. Plastics — Symbols und Abbreviated Terms. iso.org