TPI Extem (Thermoplastic Polyimide) Eigenschaften — Complete Engineering Daten Sheet (2026)
Tensile data verified against MatWeb.com database & manufacturer datasheets · Zuletzt aktualisiert July 2026
Published: 2026-05-31
Extem ist Sabic's family von amorphous thermoplastic polyimides (TPI) mit glass transition temperatures ranging von 247°C (Extem UH series) zu 350°C (Extem XH series) — der highest continuous service temperature von any melt-processable...
Extem ist Sabic's family von amorphous thermoplastic polyimides (TPI) mit glass transition temperatures ranging von 247°C (Extem UH series) zu 350°C (Extem XH series) — der highest continuous service temperature von any melt-processable (non-thermoset) polymer commercially available. Extem XH bridges der gap zwischen injection-moldable thermoplastics (PEEK service grenze ~260°C) und non-melt-processable polyimides (Vespel PI, welche müssen sein direct-formed durch powder-metallurgy sintering oder machined von stock shapes bei enormous kosten und waste). Der ability zu injection-mold ein polymer mit 300°C continuous service temperature — enabling complex geometries, threaded features, snap-fits, und thin walls das sind impossible oder kosten-prohibitive in machined Vespel — ist Extem's singular wert proposition.
Extem requires extreme processing conditions: melt temperature 400-440°C, mold temperature 160-230°C (öl-heated — pushing der limits von conventional öl units rated für 200°C), und EXTREME drying requirements (150°C für 6-8 hours zu <0.01% moisture — below the detection limit of most dew-point sensors). Standard injection molding machines are not capable of processing Extem — the barrel, screw, check ring, and hot runner system must be rated for sustained 440°C operation (specialty high-temperature machines with ceramic heater bands, liquid-cooled feed throat, and high-temperature-capable hydraulic or all-electric clamp).
Recommended Anwendungen
TPI Extem ist commonly specified für:
⚠ Nicht Recommended Für
TPI Extem ist nicht recommended für:
- Moisture absorption applications ohne sealing (Vespel PI absorbs 1-3% moisture — dimensional stability affected)
- Kosten-sensitive applications wo PAI oder PEEK suffices (PI ist 5-10× der kosten von PEEK)
- Continuous service in strong bases über 200°C (verwenden PBI für extreme alkaline widerstand)
Technical Eigenschaften
| Dichte | 1.46 g/cm³ |
|---|---|
| Zugfestigkeit | 120 MPa |
| Schmelzpunkt | N/EIN (Amorphous, Tg 350 °C) |
| Shrinkage Rate | 0.8% |
| Flexural Modulus | 5.5 GPa |
| Hdt | 330 °C bei 1.82 MPa |
| Continuous Service Temp | 300 °C |
Engineering Werkzeug: Shrinkage & Kosten Estimator
Calculate teil weight, mold cavity dimensions accounting für shrinkage, und material kosten — alle locally in ihr browser.
Equivalents & Cross-References
| Entsprechung / Alternate | Action |
|---|---|
| Sabic Extem XH | |
| DuPont Vespel TP (discontinued) | |
| Mitsui Aurum |
Frequently Asked Questions
Wenn ist Extem worth der extreme processing difficulty vs machined Vespel?
Der economic crossover depends ein teil complexity und production volume: für simple geometries (bushings, washers, seal rings) bei niedrig volumes (<1,000 teile/year), machined Vespel ist mehr kosten-effective. Für complex geometries (connectors mit snap-fits, sensor housings mit internal threads, thin-walled insulators) bei medium-zu-hoch volumes (>5,000 teile/year), injection-molded Extem ist dramatically cheaper — der mold amortization ist offset durch eliminating der machining kosten (Vespel machining können sein 5-20× der raw material kosten due zu extreme werkzeug wear und slow cutting speeds erforderlich). Extem auch enables design features impossible in machined stock shapes: living hinges (limited fatigue life bei 300°C), internal undercuts, und gas-assist hollow sections für weight reduction. Der qualification barrier ist der primär obstacle — aerospace und semiconductor OEMs haben 5-10 year material qualification timelines für neu polymers in kritisch applications, und Vespel hat ein 50-year track record.
Verwandt Diagnostics & Materials
PEEK Polyetheretherketone: Hoch-Leistung Polymer...
Polyetheretherketone (PEEK) ist ein colorless organic thermoplastic polymer in der polyaryletherketone (PAEK) family,...
Ultem PEI (Polyetherimide): Hoch-Temperatur Amorphous...
Polyetherimide (PEI), best known durch Sabic's trade name Ultem, ist ein amorphous hoch-leistung thermoplastic...
PTFE Teflon: Ultimate Chemical Widerstand & Niedrig-Friction...
Polytetrafluoroethylene (PTFE), widely known durch der trade name Teflon, ist ein fluoropolymer mit der lowest...
PPS Ryton: Polyphenylene Sulfide Hoch-Temp...
Polyphenylene sulfide (PPS), best known durch Solvay's trade name Ryton, ist ein semicrystalline hoch-leistung...
LCP Vectra: Liquid Crystal Polymer für Micro-Molding &...
Liquid Crystal Polymer (LCP), best known durch Celanese's trade name Vectra, ist ein unique class von thermotropic...
Vespel Polyimide: Extreme-Temperatur Polymer für...
Polyimide (PI), commercially known als DuPont Vespel, ist der highest-temperature-rated polymer commercially...
PAI Torlon: Polyamide-Imide Extreme-Leistung Polymer...
Polyamide-imide (PAI), commercially known als Solvay Torlon, occupies der leistung space zwischen PEEK und...
PES Veradel: Polyethersulfone Transparent Hoch-Temp...
Polyethersulfone (PES), commercially known als Solvay Veradel oder BASF Ultrason E, ist ein amorphous hoch-temperature...
References & Industry Standards
- ASTM International. Norm Specifications für Engineering Plastics & Thermoplastics. astm.org
- UL Prospector. Plastics & Elastomers Material Database. ulprospector.com
- MatWeb. Material Property Daten für Engineering Thermoplastics. matweb.com
- ISO 1043. Plastics — Symbols und Abbreviated Terms. iso.org