TPE/TPV Santoprene Eigenschaften — Complete Engineering Daten Sheet (2026)
Tensile data verified against MatWeb.com database & manufacturer datasheets · Zuletzt aktualisiert July 2026
Published: 2026-06-02
Thermoplastic vulcanizates (TPVs), solche als Santoprene (Celanese), sind dynamically vulcanized EPDM rubber particles dispersed in ein polypropylene matrix. Dies structure provides rubber-wie elasticity mit thermoplastic processability — teile können...
Thermoplastic vulcanizates (TPVs), solche als Santoprene (Celanese), sind dynamically vulcanized EPDM rubber particles dispersed in ein polypropylene matrix. Dies structure provides rubber-wie elasticity mit thermoplastic processability — teile können sein injection molded mit standard ausrüstung, und scrap ist fully recyclable. Santoprene ist der dominant TPV für automotive weather seals, appliance gaskets, und soft-touch overmolding. Härte ranges von 35 Shore EIN (sehr soft gel-wie) zu 50 Shore D (semi-rigid).
Overmolding design guidelines: TPV bonds well zu PP via melt fusion (gleich matrix material); bonds poorly zu PA66, POM, und PBT ohne mechanical interlock. Substrate surface temperature bei der point von TPV injection müssen sein über der TPV's crystallization temperature (~110°C) zu achieve bond strength — dies typically requires der rigid substrate mold temperature zu sein elevated 10-20°C über standard settings. Für chemical bonding zu engineering plastics (PA, PC/ABS, PBT), TPE-U (thermoplastic polyurethane) oder TPE-E (COPE) grades offer superior adhesion zu polar substrates.
Recommended Anwendungen
TPE/TPV Santoprene ist commonly specified für:
Technical Eigenschaften
| Dichte | 0.97 g/cm³ |
|---|---|
| Zugfestigkeit | 5-15 MPa (grade dependent) |
| Schmelzpunkt | TPV: melt processable bei 190-230°C |
| Shrinkage Rate | 1.5-2.5% |
| Flexural Modulus | 0.01-0.3 GPa |
| Hdt | Nicht applicable (elastomeric) |
Engineering Werkzeug: Shrinkage & Kosten Estimator
Calculate teil weight, mold cavity dimensions accounting für shrinkage, und material kosten — alle locally in ihr browser.
Equivalents & Cross-References
| Entsprechung / Alternate | Action |
|---|---|
| Santoprene | |
| Sarlink | |
| Forprene |
Frequently Asked Questions
Können Santoprene sein overmolded onto nylon?
TPV (Santoprene) bonds poorly zu PA66/PA6 — der PP matrix ist non-polar und tut nicht form chemical bonds mit nylon's polar amide groups. Specify TPE-U (polyurethane TPE, e.g., Desmopan) oder TPE-E (copolyester TPE, e.g., Hytrel) für overmolding onto nylon, PC, oder ABS substrates.
Was ist der maximum service temperature für Santoprene?
Santoprene grades sind rated für continuous verwenden bei 135°C (allgemein purpose) zu 150°C (hoch-heat grades). Über diese temperatures, der PP matrix softens und der EPDM rubber phase accelerates oxidative degradation. Kurz-term exposure zu 165°C ist acceptable für minutes (e.g., paint bake ovens).
Verwandt Diagnostics & Materials
PEEK Polyetheretherketone: Hoch-Leistung Polymer...
Polyetheretherketone (PEEK) ist ein colorless organic thermoplastic polymer in der polyaryletherketone (PAEK) family,...
Ultem PEI (Polyetherimide): Hoch-Temperatur Amorphous...
Polyetherimide (PEI), best known durch Sabic's trade name Ultem, ist ein amorphous hoch-leistung thermoplastic...
PTFE Teflon: Ultimate Chemical Widerstand & Niedrig-Friction...
Polytetrafluoroethylene (PTFE), widely known durch der trade name Teflon, ist ein fluoropolymer mit der lowest...
PPS Ryton: Polyphenylene Sulfide Hoch-Temp...
Polyphenylene sulfide (PPS), best known durch Solvay's trade name Ryton, ist ein semicrystalline hoch-leistung...
LCP Vectra: Liquid Crystal Polymer für Micro-Molding &...
Liquid Crystal Polymer (LCP), best known durch Celanese's trade name Vectra, ist ein unique class von thermotropic...
Vespel Polyimide: Extreme-Temperatur Polymer für...
Polyimide (PI), commercially known als DuPont Vespel, ist der highest-temperature-rated polymer commercially...
PAI Torlon: Polyamide-Imide Extreme-Leistung Polymer...
Polyamide-imide (PAI), commercially known als Solvay Torlon, occupies der leistung space zwischen PEEK und...
PES Veradel: Polyethersulfone Transparent Hoch-Temp...
Polyethersulfone (PES), commercially known als Solvay Veradel oder BASF Ultrason E, ist ein amorphous hoch-temperature...
References & Industry Standards
- ASTM International. Norm Specifications für Engineering Plastics & Thermoplastics. astm.org
- UL Prospector. Plastics & Elastomers Material Database. ulprospector.com
- MatWeb. Material Property Daten für Engineering Thermoplastics. matweb.com
- ISO 1043. Plastics — Symbols und Abbreviated Terms. iso.org