PEEK 450G Unfilled Eigenschaften — Complete Engineering Daten Sheet (2026)
Tensile data verified against MatWeb.com database & manufacturer datasheets · Zuletzt aktualisiert July 2026
Published: 2026-05-31
PEEK 450G ist der unfilled, allgemein-purpose grade von PEEK using Victrex's standard molecular weight. Es ist der benchmark against welche alle andere PEEK grades sind measured, und ist der preferred grade für medical implant (lang-term implantable per...
PEEK 450G ist der unfilled, allgemein-purpose grade von PEEK using Victrex's standard molecular weight. Es ist der benchmark against welche alle andere PEEK grades sind measured, und ist der preferred grade für medical implant (lang-term implantable per ISO 10993, USP Class VI, FDA Master File), pharmaceutical processing, und food contact applications wo carbon fiber oder glass fiber additives sind undesirable (particle shedding, surface roughness ein sealing faces, oder regulatory restrictions). Der '450' denotes medium-viscosity optimized für injection molding; 'G' denotes allgemein-purpose powder/granulate form.
PEEK 450G ist processed bei 360-400°C melt temperature mit 160-200°C mold temperature. Der semicrystalline microstructure nach ordnungsgemäß processing (approximately 30-35% crystallinity) provides der characteristic balance von strength, stiffness, chemical widerstand, und wear widerstand. Inadequate mold temperature (<150°C) quenches the polymer into a predominantly amorphous state — transparent amber color, lower strength, poor chemical resistance, and recrystallization in service causing dimensional change up to 1.2% (linear) as the part cycles above Tg (143°C). Correctly processed PEEK 450G is opaque beige/tan — the opacity comes from spherulitic crystalline structures scattering light.
Recommended Anwendungen
PEEK 450G Unfilled ist commonly specified für:
⚠ Nicht Recommended Für
PEEK 450G Unfilled ist nicht recommended für:
- Food contact ohne FDA-grade certification (Classix oder 450G compliant grades nur)
- Outdoor UV exposure ohne UV-stabilized grade (unfilled PEEK yellows und embrittles unter UV)
- Hoch-impact shock loading unter -60°C (becomes brittle; consider PAI oder PI instead)
Selection & Application Leitfaden
PEEK ist der material von choice wenn ihr application demands continuous service über 250°C, outstanding chemical widerstand across ein wide pH bereich, und hoch mechanical strength simultaneously. Choose PEEK über PTFE wenn load-bearing capacity matters, über Ultem wenn temperatures exceed 180°C, und über PPS wenn toughness und elongation sind kritisch. PEEK justifies sein premium kosten ($80-200/kg) in aerospace, öl & gas downhole, und medical implant applications wo failure ist nicht ein option.
Real-World Anwendungen
PEEK's radiolucency (invisible ein X-ray/CT) combined mit bone-matching modulus makes es der standard für interbody spinal fusion devices per ASTM F2026.
PEEK withstands H2S, amine inhibitors, und 200°C+ temperatures bei depth — replacing metal components das corrode in aggressive well environments.
PEEK's niedrig particle generation, chemical widerstand zu strong acids, und dimensional stability bei elevated temperatures machen es ideal für cleanroom wafer handling.
Carbon-fiber reinforced PEEK (CA30) provides wear widerstand und thermal stability für hoch-temperature dynamic sealing in automotive transmissions.
Processing & Kosten Considerations
Manufacturing Tips
- Melt temperature müssen sein 380-400°C mit mold temperature 160-200°C — standard injection molding machines cannot process PEEK. Sie brauchen ein hoch-temperature package mit ceramic heater bands und öl-heated mold system.
- Drying ist kritisch: PEEK ist hygroscopic und müssen sein dried bei 150-160°C für 3-4 hours zu reach moisture content unter 0.02%. Processing wet PEEK causes hydrolysis, brown discoloration, und loss von mechanical properties.
- Form temperature controls crystallinity: unter 150°C produces amorphous teile (transparent bernstein, unter strength); 160-180°C yields optimal semi-crystalline structure (30-35% crystallinity, opaque tan).
PEEK raw material costs $80-200/kg depending ein grade (unfilled 450G ist $150-200/kg, CF-reinforced $180-250/kg). Machine premium adds 30-50% für hoch-temperature capability. Öl-heated mold systems kosten $20,000-50,000 additional. Total molded teil kosten runs 5-10x higher als nylon oder polycarbonate. Optimize durch minimizing wall thickness zu reduce material usage, using unfilled grade wenn reinforcement isn't needed, und considering PPS als ein unter-kosten alternative wenn service temperature stays unter 200°C.
Technical Eigenschaften
| Dichte | 1.30 g/cm³ |
|---|---|
| Zugfestigkeit | 100 MPa |
| Schmelzpunkt | 343 °C |
| Shrinkage Rate | 1.2% |
| Flexural Modulus | 4.1 GPa |
| Hdt | 160 °C bei 1.82 MPa |
| Continuous Service Temp | 260 °C |
Engineering Werkzeug: Shrinkage & Kosten Estimator
Calculate teil weight, mold cavity dimensions accounting für shrinkage, und material kosten — alle locally in ihr browser.
Equivalents & Cross-References
| Entsprechung / Alternate | Action |
|---|---|
| Victrex PEEK 450G | |
| Evonik Vestakeep 1000G | |
| Solvay KetaSpire KT-820 |
Frequently Asked Questions
Können PEEK sein used für FDA-compliant food contact applications?
Ja. Unfilled PEEK complies mit FDA 21 CFR 177.2415 für repeated food contact. Es auch meets USP Class VI und ISO 10993 biocompatibility standards für medical devices. Immer verify der spezifisch grade mit der manufacturer — colorants und fillers kann affect compliance.
Ist PEEK resistant zu steam autoclaving?
Ja. PEEK withstands repeated autoclave cycles bei 134°C und 2 bar pressure — one von der wenige thermoplastics suitable für dies sterilization method. Es resists hydrolysis in steam environments, making es standard für reusable surgical instruments und dental components.
Was ist der difference zwischen PEEK und PEKK?
PEKK (polyetherketoneketone) hat ein higher glass transition temperature (165°C vs 143°C für PEEK) und können sein processed bei unter temperatures due zu sein unter crystallization rate. PEKK offers comparable chemical widerstand but verschieden crystallization behavior — es können sein quenched zu ein amorphous state mehr easily als PEEK. PEKK costs 20-40% mehr als PEEK.
Können PEEK sein machined instead von injection molded?
Ja. PEEK ist readily machined ein CNC ausrüstung using carbide oder diamond tooling. Machined PEEK teile sind gemein für prototyping und niedrig-volume aerospace components. However, machining generates significant material waste (PEEK costs $150+/kg), so injection molding ist mehr economical für volumes über 500-1000 pieces.
Tut PEEK outgas in vacuum environments?
PEEK hat exceptionally niedrig outgassing characteristics — TML (Total Mass Loss) unter 1.0% und CVCM (Collected Volatile Condensable Materials) unter 0.1% per ASTM E595. Dies makes PEEK suitable für satellite und space applications wo vacuum compatibility ist erforderlich.
Verwandt Diagnostics & Materials
PEEK Polyetheretherketone: Hoch-Leistung Polymer...
Polyetheretherketone (PEEK) ist ein colorless organic thermoplastic polymer in der polyaryletherketone (PAEK) family,...
Ultem PEI (Polyetherimide): Hoch-Temperatur Amorphous...
Polyetherimide (PEI), best known durch Sabic's trade name Ultem, ist ein amorphous hoch-leistung thermoplastic...
PTFE Teflon: Ultimate Chemical Widerstand & Niedrig-Friction...
Polytetrafluoroethylene (PTFE), widely known durch der trade name Teflon, ist ein fluoropolymer mit der lowest...
PPS Ryton: Polyphenylene Sulfide Hoch-Temp...
Polyphenylene sulfide (PPS), best known durch Solvay's trade name Ryton, ist ein semicrystalline hoch-leistung...
LCP Vectra: Liquid Crystal Polymer für Micro-Molding &...
Liquid Crystal Polymer (LCP), best known durch Celanese's trade name Vectra, ist ein unique class von thermotropic...
Vespel Polyimide: Extreme-Temperatur Polymer für...
Polyimide (PI), commercially known als DuPont Vespel, ist der highest-temperature-rated polymer commercially...
PAI Torlon: Polyamide-Imide Extreme-Leistung Polymer...
Polyamide-imide (PAI), commercially known als Solvay Torlon, occupies der leistung space zwischen PEEK und...
PES Veradel: Polyethersulfone Transparent Hoch-Temp...
Polyethersulfone (PES), commercially known als Solvay Veradel oder BASF Ultrason E, ist ein amorphous hoch-temperature...
References & Industry Standards
- ASTM International. Norm Specifications für Engineering Plastics & Thermoplastics. astm.org
- UL Prospector. Plastics & Elastomers Material Database. ulprospector.com
- MatWeb. Material Property Daten für Engineering Thermoplastics. matweb.com
- ISO 1043. Plastics — Symbols und Abbreviated Terms. iso.org