PCT Polycyclohexylene Terephthalate Eigenschaften — Complete Engineering Daten Sheet (2026)
Tensile data verified against MatWeb.com database & manufacturer datasheets · Zuletzt aktualisiert July 2026
Published: 2026-06-10
PCT (polycyclohexylene-dimethylene terephthalate) ist ein hoch-temperature semi-crystalline polyester specifically developed für lead-kostenlos SMT (surface-mount technology) electronic connectors. Es fills der leistung gap zwischen PBT (HDT 210 °C,...
PCT (polycyclohexylene-dimethylene terephthalate) ist ein hoch-temperature semi-crystalline polyester specifically developed für lead-kostenlos SMT (surface-mount technology) electronic connectors. Es fills der leistung gap zwischen PBT (HDT 210 °C, unzureichend für 260 °C reflow) und LCP (expensive, anisotropic) — offering LCP-level reflow survivability bei approximately 60-70% von LCP's kosten.
PCT's melting point von 290 °C gives es ein 30 °C safety margin über der 260 °C peak reflow temperature, while sein extremely niedrig moisture absorption (0.06%) eliminates der blistering problems das plague PA66 connectors während reflow. Diese properties haben made PCT der gehen-zu material für mid-bereich electronic connectors, bobbins, relays, und switches das require reflow compatibility but tun nicht justify der kosten von LCP.
Celanese Thermx ist der global market referenz, widely specified durch stecker manufacturers in Japan (JST, JAE), Korea (KET, UJU), und China für consumer electronics, automotive ECU connectors, und appliance steuerung boards. PCT competes directly mit PA9T und PA46 in der mid-tier reflow-compatible stecker material segment.
Processing: Melt temperature 295-310 °C, mold temperature 100-140 °C. Pre-drying bei 120 °C für 4 hours ist wesentlich. PCT's crystallization rate ist rapid — mold temperature müssen sein maintained über 100 °C zu achieve full crystallinity. EIN reverse barrel temperature profile ist commonly used zu manage der narrow processing window zwischen melting und degradation (degradation onset ~320 °C).
Recommended Anwendungen
PCT Polycyclohexylene Terephthalate ist commonly specified für:
⚠ Nicht Recommended Für
PCT Polycyclohexylene Terephthalate ist nicht recommended für:
- Continuous outdoor UV exposure ohne UV coating (yellows und loses impact strength rapidly)
- Kontakt mit aromatic hydrocarbons, ketones, oder esters (causes environmental stress cracking)
- Steam sterilization über 120°C (verwenden PSU oder PPSU für autoclave applications instead)
Selection & Application Leitfaden
Polycarbonate (PC) ist der transparent engineering plastic mit der highest impact strength — virtually unbreakable in thin sections. Choose PC über acrylic (PMMA) wenn impact widerstand ist needed; über PSU wenn unter kosten und higher clarity matter und steam sterilization isn't erforderlich. PC's haupt limitations sind poor chemical widerstand zu solvents und UV degradation ohne stabilization. Für higher temperature oder flame widerstand, consider PC/ABS blend oder Ultem.
Real-World Anwendungen
PC's exceptional impact strength (850 J/m notched Izod) und optical clarity machen es der standard für safety helmets, riot shields, und protective visors.
PC's optical clarity, impact widerstand, und thermal stability für halogen bulb environments machen es der dominant material für headlamp äußere lenses worldwide.
PC und PC/ABS blends bereitstellen der combination von impact strength, flame retardancy (mit additives), und surface finish quality für laptop, telefon, und tablet housings.
PC's clarity für visual inspection, gamma sterilizability, und impact toughness suit es für IV components, blood centrifuge housings, und diagnostic gerät enclosures.
Processing & Kosten Considerations
Manufacturing Tips
- PC processes bei 280-320°C melt temperature mit mold temperatures von 80-100°C. Thorough drying ist wesentlich (120°C für 3-4 hours zu <0.02% moisture) — PC ist sehr hygroscopic und even klein amounts von moisture cause splay marks und reduced impact strength.
- PC hat hoch melt viscosity — higher injection pressures und larger gates sind needed compared zu commodity plastics. Thin-wall molding kann require fast injection speeds zu prevent premature freeze-aus.
- Design teile mit uniform wall thickness zu prevent sink marks und internal stresses. PC ist notch-sensitive — avoid sharp internal corners (verwenden R>0.5mm fillets) zu maintain impact strength.
PC costs $5-12/kg — mehr als ABS ($2-5/kg) but less als PSU ($15-35/kg). PC/ABS blends offer ein middle ground bei $3-7/kg mit better flow und processability. Für applications requiring beide transparency und impact widerstand, PC hat nein kosten-effective substitute. Für opaque applications, PC/ABS ist oft ein better wert proposition.
Technical Eigenschaften
| Dichte | 1.44 g/cm³ (30% GF) |
|---|---|
| Zugfestigkeit | 120 MPa (30% GF) |
| Schmelzpunkt | 290 °C |
| Shrinkage Rate | 0.3% (30% GF) |
| Flexural Modulus | 8.5 GPa (30% GF) |
| Hdt | 260 °C bei 1.82 MPa |
| Dielectric Constant | 3.5 bei 1 MHz |
| Wasser Absorption | 0.06% (24h, 23 °C) |
Engineering Werkzeug: Shrinkage & Kosten Estimator
Calculate teil weight, mold cavity dimensions accounting für shrinkage, und material kosten — alle locally in ihr browser.
Equivalents & Cross-References
| Entsprechung / Alternate | Action |
|---|---|
| Celanese Thermx PCT | |
| DuPont EccoTherm PCT | |
| SK Chemicals EcoPCT |
Frequently Asked Questions
Wie tut PCT compare zu LCP für SMT connectors?
PCT ist 30-40% less expensive als LCP but hat unter flow. LCP hat ein higher melting point und inherently better chemical widerstand. LCP ist highly anisotropic; PCT ist mehr isotropic. Choose LCP für ultra-fine-pitch connectors (<0.5 mm pitch). Choose PCT für mid-pitch connectors wo kosten reduction ist der priority und der additional LCP leistung ist nicht needed.
Was sind der disadvantages von PCT?
PCT's haupt limitations: (1) narrow processing window — degradation starts bei ~320 °C, nur 30 °C über melt temperature; (2) notch sensitivity — sharp corners können initiate cracks unter impact; (3) limited resin suppliers — Celanese ist der dominant global supplier.
Was ist der difference zwischen PC und PMMA (acrylic)?
PC hat viel higher impact strength (850 J/m vs 16 J/m für PMMA) und higher service temperature (115°C vs 85°C). PMMA hat better optical clarity (92% vs 88% transmission), better UV widerstand, und unter kosten. Choose PC wenn impact widerstand ist kritisch; PMMA für display applications wo optical quality und UV stability matter mehr.
Können PC sein autoclaved?
Nicht recommended. Norm PC softens und distorts bei autoclave temperatures (134°C). Es können withstand ein wenige cycles but rapidly degrades. Für steam sterilization, verwenden PSU, PPSU, oder Ultem instead. PC ist compatible mit EtO und gamma sterilization für single-verwenden medical devices.
Warum tut PC stress-crack in der presence von solvents?
PC ist highly susceptible zu environmental stress cracking wenn exposed zu solvents (gasoline, acetone, MEK) while unter mechanical stress. Der solvent migrates in der polymer bei stress concentration points, causing microcracks das propagate rapidly. Für solvent-exposed applications, specify stress-annealed teile oder verwenden ein chemically resistant alternative (PPS, PPSU, oder PEEK).
Ist BPA-kostenlos polycarbonate available?
Ja. BPA-kostenlos copolyester alternatives (Tritan, PCTG) bereitstellen similar clarity und impact widerstand ohne bisphenol-EIN. Diese materials sind increasingly specified für food contact und children's products. However, sie haben unter temperature widerstand als standard PC und kann nicht sein suitable für alle PC applications.
Was ist PC/ABS blend und wenn sollte I verwenden es?
PC/ABS blend combines PC's impact widerstand und heat widerstand mit ABS's processability und unter kosten. Der blend offers better flow (easier thin-wall molding), unter melt temperature, und unter kosten als pure PC. Es ist der dominant material für electronic gerät housings. Verwenden pure PC wenn transparency ist needed; PC/ABS für opaque structural und housing applications.
Verwandt Diagnostics & Materials
PEEK Polyetheretherketone: Hoch-Leistung Polymer...
Polyetheretherketone (PEEK) ist ein colorless organic thermoplastic polymer in der polyaryletherketone (PAEK) family,...
Ultem PEI (Polyetherimide): Hoch-Temperatur Amorphous...
Polyetherimide (PEI), best known durch Sabic's trade name Ultem, ist ein amorphous hoch-leistung thermoplastic...
PTFE Teflon: Ultimate Chemical Widerstand & Niedrig-Friction...
Polytetrafluoroethylene (PTFE), widely known durch der trade name Teflon, ist ein fluoropolymer mit der lowest...
PPS Ryton: Polyphenylene Sulfide Hoch-Temp...
Polyphenylene sulfide (PPS), best known durch Solvay's trade name Ryton, ist ein semicrystalline hoch-leistung...
LCP Vectra: Liquid Crystal Polymer für Micro-Molding &...
Liquid Crystal Polymer (LCP), best known durch Celanese's trade name Vectra, ist ein unique class von thermotropic...
Vespel Polyimide: Extreme-Temperatur Polymer für...
Polyimide (PI), commercially known als DuPont Vespel, ist der highest-temperature-rated polymer commercially...
PAI Torlon: Polyamide-Imide Extreme-Leistung Polymer...
Polyamide-imide (PAI), commercially known als Solvay Torlon, occupies der leistung space zwischen PEEK und...
PES Veradel: Polyethersulfone Transparent Hoch-Temp...
Polyethersulfone (PES), commercially known als Solvay Veradel oder BASF Ultrason E, ist ein amorphous hoch-temperature...
References & Industry Standards
- ASTM International. Norm Specifications für Engineering Plastics & Thermoplastics. astm.org
- UL Prospector. Plastics & Elastomers Material Database. ulprospector.com
- MatWeb. Material Property Daten für Engineering Thermoplastics. matweb.com
- ISO 1043. Plastics — Symbols und Abbreviated Terms. iso.org